In American practices, you will find many people using porcelain veneers. This is notwithstanding the fact that many dental institutions do not offer training in this. Porcelain veneers work well with many patients, but it is important that one takes them as part of the diagnosis process. This should be taken alongside options such as bleaching, direct bonding traditional orthodontics and aesthetic recontouring. In case you are wondering how the no prep veneers Houston processes occur, this will be a guide into this.
The first thing that a dentist does is to get the ones that fit for the patient. The way this is done is by trying them without using paste for easy fitting. Once the dentist has ascertained that each fits well, the next thing that he does is to try the units together and check the contact. For this procedure try-in cement will be used to hold them in place. Once this is done, one is then given a mirror to check how they look on them and tell whether they are comfortable.
The try-in cement is then made water soluble. The importance of this procedure is to ensure that all the internal elements that the veneers may leave behind can be cleaned up easily. There is usually a pumice prepared before which is them mixed with some liquid consepsis which is used to clean the teeth. After this, the teeth will then be dried using air.
The procedure that follows this is etching of the teeth with phosphoric acid of 37% concentration for about 15 seconds. This is then rinsed off, and the teeth are left to dry. The picture that one gets, in this case, is frosty that is associated with the etching enamel. The dentist will then prepare a thin layer of a scotch bond adhesive and places it using a micro brush.
The dentist then takes the veneer cement and applies it on the veneer and places it on the tooth. Extra cement is left to remain visible, and if it cannot be seen, the veneer is removed, and then more cement is added until he is sure that it can be seen on the margins. This procedure is repeated for all veneers.
The dental assistant will then take the LED emetron light and holding it about 5-7mm away from the extra cement waves this lights back and forth for about 5 seconds. What this is aimed at is to make the cement get into a gel form without it going through the complete curing process.
Once the gingival margin gets cleaned up, light is then placed halfway on its tissues and halfway on its margins. The reason this is done is to finish up the curing process and get the veneer to hold on well in its place. To clean the excess cement, flossing is done to get it out before it can entirely cure on the sides.
Completion of the curing process is with the cleaning of the cement. The centrals are then placed first as they are the most important when it comes to completing the process successfully and for esthetic purposes. Working with the right dentist will ensure that you get the best result. So you want to first look into the experience of the dental practitioner and the reputation that he has out there before deciding to visit the doctor.
The first thing that a dentist does is to get the ones that fit for the patient. The way this is done is by trying them without using paste for easy fitting. Once the dentist has ascertained that each fits well, the next thing that he does is to try the units together and check the contact. For this procedure try-in cement will be used to hold them in place. Once this is done, one is then given a mirror to check how they look on them and tell whether they are comfortable.
The try-in cement is then made water soluble. The importance of this procedure is to ensure that all the internal elements that the veneers may leave behind can be cleaned up easily. There is usually a pumice prepared before which is them mixed with some liquid consepsis which is used to clean the teeth. After this, the teeth will then be dried using air.
The procedure that follows this is etching of the teeth with phosphoric acid of 37% concentration for about 15 seconds. This is then rinsed off, and the teeth are left to dry. The picture that one gets, in this case, is frosty that is associated with the etching enamel. The dentist will then prepare a thin layer of a scotch bond adhesive and places it using a micro brush.
The dentist then takes the veneer cement and applies it on the veneer and places it on the tooth. Extra cement is left to remain visible, and if it cannot be seen, the veneer is removed, and then more cement is added until he is sure that it can be seen on the margins. This procedure is repeated for all veneers.
The dental assistant will then take the LED emetron light and holding it about 5-7mm away from the extra cement waves this lights back and forth for about 5 seconds. What this is aimed at is to make the cement get into a gel form without it going through the complete curing process.
Once the gingival margin gets cleaned up, light is then placed halfway on its tissues and halfway on its margins. The reason this is done is to finish up the curing process and get the veneer to hold on well in its place. To clean the excess cement, flossing is done to get it out before it can entirely cure on the sides.
Completion of the curing process is with the cleaning of the cement. The centrals are then placed first as they are the most important when it comes to completing the process successfully and for esthetic purposes. Working with the right dentist will ensure that you get the best result. So you want to first look into the experience of the dental practitioner and the reputation that he has out there before deciding to visit the doctor.
About the Author:
To benefit from no prep veneers Houston dental patients are advised to use this excellent clinic. Make an appointment now through this website http://tophoustoncosmetic.dentist.
No comments:
Post a Comment